Introduction to Radio-controlled Meter Time Synchronization Software
The BPC (Chinese Code) radio-controlled watch time simulation software simulates sending BPC (Chinese Code) radio waves. It only needs a computer and a pair of ordinary headphones to time the BPC code radio-controlled watch with the local time, so that the radio-controlled watch and the computer time are synchronized. I use a laptop or WIN8 tablet to send out waves, and one of my radio-controlled clocks and a radio-controlled watch can receive the waves normally, usually within 2 minutes.
The BPC (Chinese code) radio-controlled time synchronization simulation software includes a local computer time adjustment function using the NTP protocol. It can prompt the time deviation between the local time and the server standard time, and the network delay. It is very intuitive. It can also modify, add or delete the NTP server address by itself to cope with server failure. Using this function to adjust the local time is also a good choice.
Features of radio-controlled watch time setting function
NTP server: The address of the NTP timing server, 27 are built-in.
Calibrate the local time: Get the NTP standard time and calibrate the local time.
Query the standard time: only obtain the NTP standard time and display the time deviation and network delay, without correcting the local time.
Modify the server: Modify, add, and delete the NTP server address yourself, and you can delete the failed server.
Start sending waves: Use headphones to simulate sending BPC (Chinese code) radio waves, and time the radio-controlled watch with local time.
Stop sending waves: Stop sending BPC (Chinese Code) waves.
Wave sending mode: Select the wave sending mode.
Information box: Displays software running information.
Radio controlled watch time setting instructions
1. Calibrate the local time, this step is not necessary.
2. Adjust the radio-controlled watch to the BPC code forced reception state.
3. Connect the headphones to the headphone output port of the computer and adjust the volume to maximum.
4. Fix the earphones to the position of the radio-controlled watch’s receiving antenna.
5. Select the wave mode.
6. Start sending waves. At this time, the earphones make a harsh beeping sound. Wait until the radio-controlled watch successfully collects the waves and sets the time.
7. Stop sending waves.
Things to note when setting radio controlled watches
01. This software is positioned to test the wave receiving function of the radio-controlled watch. The actual timing is affected by various factors, and the timing accuracy of the radio-controlled watch will not be very accurate.
02. This software can only simulate BPC (Chinese code) timing waves.
03. The radio-controlled watch must be adjusted to the BPC code forced reception state. Of course, the radio-controlled watch can also be in the automatic receiving period.
04.耳机音量尽量调到最大。
05. Keep the earphones as close to the antenna of the radio-controlled watch as possible. You can adjust the position and direction of the earphones, or wrap the earphone wire around the radio-controlled watch. In short, you can try and toss in various ways.
06. Change a pair of headphones or a different computer.
07. The wave generation time can be longer.
08. Keep the radio-controlled watch as far away from the computer host and monitor as possible to reduce interference.
09. It is recommended to use it in places where the Shangqiu radio tower timing signal cannot be received or when the radio tower suspends wave transmission, otherwise it may interfere with each other and fail to synchronize the time.
10. When the display time of a certain domestic BPC radio-controlled watch is too different from the standard time, it cannot successfully synchronize the time in the manual forced wave collection state, but it can collect the wave normally in the automatic wave collection state.
11. If the radio-controlled watch still cannot successfully collect waves after various attempts, it may be that the wave-collecting function of your radio-controlled watch is broken or you bought a fake radio-controlled watch, or it may be that this software is incompatible with your radio-controlled watch. You can delete this software from your computer.
12. If the school time fails, please "run" the software as administrator.
Radio controlled watch time update log
1. Fixed BUG, the new version has a better experience
2. Some pages have been changed
Special instructions:
Hello, the software you are about to use is an auxiliary tool and may be intercepted and checked by major anti-virus software. This software may have risks, please pay attention to avoid it. If you want to continue using it, it is recommended to close various anti-virus software before use.
Attached is the software package decompression password: softwaredownload4.com
Huajun editor recommends:
This software for radio controlled time adjustment is completely fool-proof and super simple. In addition, the editor also recommends it.Desktop timer (Metro Timer),desktop clock,SnapTimer,bero countdown software,Calendar Maker (Photo Calendar Maker)Download and use related software.
Useful
Useful
Useful