o(╥﹏╥)oSad

WeChat cannot downloadMitsubishi plc programming cable USB driver, but just click on the upper right corner and select open in browser or Safari!
Mitsubishi plc programming cable USB driver

Mitsubishi plc programming cable USB driver

  • Size: 0.31M
  • Language: Simplified Chinese
  • Category: Peripheral driver
  • System: WinAll

Recommended for you: Mitsubishi plc driver Mitsubishi plc software

Mitsubishi plc programming cable USB driverThe official version is a PLC programming cable driver. Mitsubishi PLC programming cable USB driver is mainly used to solve the problem that Mitsubishi PLC programming cable cannot be recognized by the computer or cannot be used normally.Mitsubishi plc programming cable USB driverIt can also support all versions of windows systems. Huajun Software Park provides download services for Mitsubishi plc programming cable USB driver. To download other versions of Mitsubishi plc programming cable USB driver, please go to Huajun Software Park!

Mitsubishi plc programming cable USB driver software features

​ 1. Supported operating system Windows2000/Windows XP

​​ 2. Fully compatible with USB V1.1 and USB CDC V1.1 specifications

3. USB bus power supply (non-isolated cable), or USB bus power supply and PLC programming port power supply at the same time (isolated cable)

​​ 4. Baud rate: 300bps~1Mbps automatically adapts

5. Each PC only supports one USB programming cable

Mitsubishi plc programming cable USB driver installation instructions

​​ 1. Turn on the power of the computer to which the USB programming cable will be connected, and confirm that the computer's USB port is started and working normally.

​​ 2. Plug the USB programming cable into the USB port of your computer. Windows will detect the device and run the Add New Hardware Wizard to help you set up the new device. Insert the driver CD and click Next to continue.

If Windows does not prompt that it found new hardware, in the hardware list of Device Manager, expand "Universal Serial Bus Controllers", select the USB device with the question mark, right-click and run Update Driver.

Mitsubishi plc programming cable USB driver precautions

​​ 1. If the USB programming cable plugged into the computer is not detected when the computer is turned on (the COM port corresponding to the cable does not appear in the Windows Device Manager) or other abnormalities occur, please unplug and plug the USB plug again.

​​ 2. USB to UART is a plug-and-play USB device. It cannot be disconnected during data transmission (disconnection refers to unplugging the USB cable from the USB socket). That is to say, the cable must be unplugged from the USB socket after the application closes the serial port.

​ 3. Sometimes USB communication abnormalities may occur when the Windows system fails or the USB cable is unplugged and plugged in during communication. In this case, the computer and PLC may need to be restarted.

4. Generally speaking, it is best to plug the USB cable into the USB socket first, and then plug the other end of the programming cable into the PLC communication port after the computer detects the COM port. Because some PLCs work in master station mode, their communication ports are always sending data to me. If you plug the cable into the PLC port first, it will slow down the computer's ability to correctly identify the COM port.

Mitsubishi plc programming cable USB driver FAQ

      Question: Mitsubishi plc programming cable USB driver cannot be installed?

Answer: Please check whether your driver CD is in good condition, whether it was installed according to the installation method above, whether the cable is plugged into the computer, and whether the driver has been installed twice.

      Question: Can't communicate with the USB driver after installing the Mitsubishi PLC programming cable?

Answer: After the driver is installed, right-click "My Computer" -> "Properties" -> "Hardware" -> "Device Manager" -> double-click "Port" on the desktop. At this time, a new USB (COM port) will be generated in the computer. Then your PLC programming software must be changed to be consistent with this COM port to allow normal communication.

Mitsubishi plc programming cable USB driver system requirements

Before using the USB programming cable, please confirm that your computer is IBM PC compatible and has the following minimum system requirements:

​ 1. Intel compatible 586DX4-100MHz central processor or higher

​​ 2. A standard USB interface (4-pin A-type socket)

3. The operating system is Windows 2000 or Windows XP

Comparison of similar software

      ZOZEN fingerprint sensor universal USB driverIt is a fingerprint sensor USB driver installation program officially released by Hangzhou Zhongzheng. If the fingerprint sensor encounters problems such as failure or unresponsiveness and needs to be debugged on the computer, you must install this Zhongzheng fingerprint sensor universal USB driver.

      ZTE Mighty 3 mobile phone driverIt is the first new model of ZTE's Red Bull v5 mobile phone to be driven by the Mighty 3 after the name change. The ZTE Mighty 3 system is ZTE's own nubia UI 3.0 system, based on Android 5.1. If you buy this phone and want to flash it, you must install this ZTE Power 3 mobile phone driver.

Huajun editor recommends:

Mitsubishi plc programming cable USB driverIt is mainly used to solve the problem that Mitsubishi PLC programming cable cannot be recognized by the computer or cannot be used normally. It is highly recommended to download the Mitsubishi PLC programming cable USB driver. Whoever uses it will know. Anyway, I have already used it. Welcome to click to download and experience!

Version: 2.1 Official version | Update time: 2024-12-25

Similar recommendations

Latest updates

Mitsubishi plc programming cable USB driver review

  • 1st floor Huajun netizen 2022-02-19 17:56:26
    The overall feeling of the Mitsubishi PLC programming cable USB driver is good, I am quite satisfied, the installation and operation are very smooth! It went very smoothly following the installation step-by-step guide!
  • 2nd floor Huajun netizen 2022-02-13 16:32:26
    Mitsubishi plc programming cable USB driver is not bad, the download is very fast, I give you a good review!
  • 3rd floor Huajun netizen 2021-10-29 09:29:23
    Mitsubishi plc programming cable USB driver hopes to get better and better, come on!

Recommended products

everyonealso likeThese:

+

This application has not passed real-name authentication. You can download it through the mobile assistant.

CancelOK