lblink802.11n wireless network card driver

lblink802.11n wireless network card driverThe official version is a driver created for LBLINK802.11n wireless network card. LBLINK802.11n Wireless Network Card Driver The latest version can support WindowsXP and Win7 systems, including drivers and wireless client management software Realtek 11n usb wireless lan Utility. andlblink802.11n wireless network card driverBlock confirmation, frame aggregation and other technologies have also been used to greatly improve the efficiency of the MAC layer. Huajun Software Park offers download services for LBLINK802.11n wireless network card driver. Welcome everyone to come and use!

LBLINK802.11n wireless network card driver Basic introduction

LBLINK802.11N wireless network card driver is the driver of the LB Link 150M wireless network card, using Taiwan Ruyu 11n 150M RTL8188CUS chip. A built -in smart antenna, the signal and the early U disk network card are equivalent. ALED data transmission indicator. WPS one -click encryption switch. None of the shrinking. The volume can be super -sold in the market now. Little Bluetooth blending is quite equally. I have to sigh the speed of technology. Support WindowsXP and Win7 systems, including drivers and wireless client management software Realtek 11n usb wireless Lan Utility.

LBLINK802.11N wireless network card driver feature features

802.11n is mainly combined with the optimization of the physical layer and Mac layer to fully improve the throughput of WLAN technology.

The main physical layer technology involves MIMO, MIMO-OFDM, 40MHz, SHORT GI and other technologies, thereby raising the physical layer to 600Mbps.

If it only increases the rate of physical layers and does not optimize the MAC protocol layer such as empty port access, the physical layer optimization of the 802.11N will not be able to play. It's like even if a very wide road is built, but if the scheduling management of traffic can not keep up, congestion and inefficiency will still occur. Therefore, 802.11n uses Block confirmation, frame aggregation and other technologies for Mac, greatly improving the efficiency of the Mac layer.

802.11n can increase the transmission rate of WLAN from 54Mbps provided by the current 802.11a and 802.11g to 300Mbps or even 600Mbps. Thanks to MIMO, which combines MIMO (more income) and OFDM (orthogonal frequency division) technology OFDM technology has improved the quality of wireless transmission and also greatly improved the transmission rate.

In terms of coverage, 802.11n uses intelligent antenna technology. The antenna array composed of multiple independent antennas can dynamically adjust the beam to ensure that the WLAN users receive a stable signal and reduce the interference of other signals. Therefore, its coverage can be expanded to several square kilometers, which greatly improves WLAN's mobility.

802.11n uses a software radio technology in terms of compatibility. It is a complete and programmable hardware platform that allows the base stations and terminals of different systems to achieve interoperability and compatibility through different software on this platform. This makes WLAN compatible Sex has been greatly improved. This means that WLAN will not only achieve 802.11n compatibility, but also combine WLAN and wireless wide -area networks, such as 3G.

LBLINK802.11N Wireless network card driver installation step

1. Download the LBLINK802.11n wireless network card driver in the Huajun Software Park, decompress it into the current folder, click the Setup.exe application in it, enter the installation wizard interface, and then click Next.

2. lblink802.11n wireless network card driver is being installed, and users need to wait patiently for a while.

3. LBLINK802.11n wireless network card driver installation is over, click to complete.

LBLINK802.11n wireless network card driver Frequent problems

      Q: How can LBLINK802.11n wireless network card driver be driven?

Answer: It is recommended to reinstall the driver.

Uninstall this driver in the device manager and restart.

After the U disk is installed, use Ultraiso software to open the downloaded system installation disk file ISO file, execute the writing image file to insert the U disk to the computer, click OK, and wait for the program to execute. The U disk used, and the system can be reinstalled after booting the machine with this done system U disk to boot the machine.

The hard disk installation and premise is that there is a Windows system that can run normally, extract the downloads of the downloaded ISO file and the installation system in the non -system partition of the computer. Confirm the automatic installation operation again. Pay attention to backup before execution.

      Q: LBLINK802.11n Wireless Network Card Driver has an exclamation mark solution?

Answer: If an exclamation mark appears, it means that the wireless network will be unavailable. You can thoroughly clean up and uninstall the residual information according to the following steps:

Win+R Open the "Run" window-> Enter Regedit Mix the Registry-> Click Edit -Find, Enter the Driven Name-> Delete them all -> Close -> Restart -> Equipment Manager -> Find 802.11n -> Wizard installation is successful!

Lblink802.11n wireless network card driver

Answer: ① First of all, make sure that the computer's network is unblocked (the icon is not red large fork). There are wireless network card equipment. Right -click the start menu and click the CMD command prompt window icon icon → click in the menu to run as an administrator.

② Enter the following command in the command prompt window (press the Enter key to execute the command):

Netsh WLAN SET HOSTEDNETWORK MODE = Allow SSID = Computers everyone has key = 123456

Related instructions: SSID → The user name of the wireless network (can be customized) key → is a wireless password (can also be customized)

③ As long as the command is correct, it will take effect. And also show the following prompts:

The loading network mode has been set to allow.

It has been successfully changed to SSID on the Internet.

The user key password of the hosting network has been successfully changed.

④ Start → Run → Enter: NCPA.CPL Press the Enter key to open the network connection, and there will be an additional virtual wireless connection (at this time it cannot be used normally).

⑤ Then enter the command of the launching network in the command prompt window (press the Enter key):

Netsh Wlan Start Hostednetwork

The successful execution command will have a prompt: the carrying network has been started.

⑥ Go to the network connection to check again. At the bottom left of this wireless connection icon, there is no disabled red fork. Open the mobile phone of the mobile phone, conduct SSID search, and then enter the password to share WiFi.

⑦ If you want to close the bearer network, you can also use the command (press Enter Enter key):

Netsh Wlan Stop Hostednetwork

Similar software comparison

      Win11 wireless network card driverThe official version is a powerful wireless network card driver installation tool. The latest version of Win11 wireless network card driver has high bandwidth, high -quality unlimited network service functions, which can help users reach the Ethernet network level. Win11 wireless network card driver supports various models of wireless network card equipment, and also supports the new Windows11 operating system.

      Mercury wireless network card driver universal versionThe official version is a driver for the Mercury network card series. The official version of the Mercury wireless network card driver has functions such as WiFi receiving, WIFI sharing, and analog AP using network cards. And the universal version of the Mercury wireless network card driver can also solve the situation where your computer cannot use wireless network cards.