In order to use Altium Designer conveniently and quickly, we often use some shortcut keys. So do you know what the ad shortcut keys are? Next, the editor will bring you a summary of ad shortcut keys, hoping to help you use Altium better. Designer.
R+L Outputs the wiring length of all nets in the PCB
Ctrl + left-click to complete the automatic wiring connection of the line being routed
● M+G can change the shape of copper;
● Press P+T in the wiring state, press Shift+A to directly conduct snake wiring
● T+R Perform the snake wire wiring on the complete line
● E ++ M+C click to quickly find the components you want on the PCB
Backspace undoes the previous operation of routing
Switch wiring layers and place vias during the wiring process
● Ctrl+Shift switches layers and places vias
● F8/E+O+S sets the center point of the circle
● M+I flips the selected component
● P+T wiring
T+E Tear Drop Replenisher
● P+G copper laying
● S+Y single layer selection line
● E+B select to copy
● Ctrl+O Open folder/document
● Ctrl+P print settings
● Esc to exit from the current step
● Shift + mouse wheel to move left/right
V + D View document
● V + F to view objects suitable for placement
● V + B View the reverse layout
● E + D delete object
● Shift + R switches between three routing modes (ignore, avoid or push other signal lines)
● Shift + E triggers electrical grid on/off
● Shift + C cancel highlighting
● Ctrl + G Pops up the snap grid dialog box
● Ctrl + M measure distance
● Ctrl + H Select the wiring of a certain network under PCB to facilitate deleting the wiring of the same network
● R + M measures the distance between any two points
● Q Quickly switch units (metric/imperial)
Shist + Right-click to rotate to view 3D view
● Select + Space to rotate components
● P + L draw line
● P+ N Place the network mark
● Shift+S switches between single-layer display and multi-layer display
● In the process of interactive wiring, the shift + space key switches the wiring shape
● Shift+M partial magnification function
● shift + w switches the wiring width
● shift + v switches vias
● shift+ctrl+space /shift + space to switch wiring forms
Ctrl + Shift + L, R, T, B, H, V When selecting two or more devices, align left, right, top, bottom, horizontal, vertical
● D+ O schematic document option settings
● G switching grid
● Space 90 degree flip/switch wiring
● 2/3 2D/3D switch back and forth
● Ctrl+shift+wheel layer switching
● Left click + X/Y Flip left and right/up and down
● P+W schematic diagram connection
● P+B schematic diagram placement bus
● P+J schematic diagram to place circuit nodes
● P + R schematic placement port
● P + I + N schematic ignores ERC check
● Ctrl + shift + V array paste
● TAB key is used to pop up the properties of the operation
● shift + s to switch to displaying a single layer
● P + P place pad
● P + V place vias
● P + G place copper pour
● P + T placement trace
L display layer
● P+F Place filling
● T + D + R design rule check
● D + R rule settings
V + B PCB 3D Flip
● D + O schematic paper size setting
● D + K Open PCB layer manager
● Right-click + T to start wiring with the same network label
● M + M Mobile Components
● S + L two left -button twice, select multiple lines to run at the same time
● Drag the component + L to quickly switch between the top and bottom layers of the component
● T + U delete all wiring (all)
● J + C Search for components in PCB
● T + C schematic components and PCB components are positioned relative to each other
N + SHOW / HIDE displays and hides the flying line
● T + T + M multiple pull wires
● A + P text position selection
● T + M Reset DRC
● Ctrl + (shift) + Tab switch document display
● T + R 1.2.3.4. The comma. The end -length and snake -shaped line; adjust the corner and arc; adjust the width; change the amplitude
● Alt + left -button principle diagram of the same network search
The above is the summary of ad shortcut keys brought by the editor. Friends in need should not miss it.
