In the process of using CAM350, shortcut keys are often used. So do you know what the shortcut keys and commands of CAM350 are? The following is a collection of shortcut keys and commands for CAM350. Friends in need can take a look. oh.
Application of letter keys
Q: View D code and tool and set them as current
W: When there is no selection command, it is a frame selection to enlarge the window; when there is a selection command, it is a frame selection.
R: refresh
T: Transparent display
Y: Open layer list
U: Undo
I: It has no effect when there is no selection command. When there is a selection command, +W in front is to invert the selection.
O: When there is an angle command, it is: 04590 degrees to switch between each other
P: Return to the last window
A: Open the D code table
S: The cursor moves with the grid points
D: Open the D code table and set it as the current D code
F: Switch between one-dimensional line, two-dimensional line and zero line width.
G: Opening a small window has no effect
H: Highlight the current D code or tool
K: Close a layer except the current layer
L: Open a layer and set it as the current layer
Z: Turn on automatic snapping of midpoint
X: Cursor switching
C: When there is no selection command, the window is enlarged and the cursor is in the center of the window. When there is a selection command, +W in front of it is to frame the part and the entire object or network can be selected.
V: Turn on grid display
N: Negative display
" ,": Repeat the last command
Home: Full screen display
Page UP: Zoom in to capture center
Page Down: Reduce snap center
Insert moves the cursor in the opposite direction of the window
document
Alt+F+N New
Alt+F+O Open
Alt+F+S Save
Alt+F+M merge films
Alt+F+I+U automatic import
Alt+F+I+G Import Gerber
Alt+F+I+R Import drill tape
Alt+F+I+M import gong tape
Alt+F+I+X Import DXF document (CAD design)
Alt+F+E+G to export Gerber
Alt+F+E+C Export composite layer
Alt+F+E+R Export drill zone
Alt+F+E+M Export Gong Band
Alt+F+E+X Export DXF document (CAD designed)
Alt+F+P+P Print
edit
U Undo (can undo 16 consecutive steps)
Ctrl+U restore (can operate for 16 consecutive steps)
Alt+E+M Move
Alt+E+C copy
Alt+E+D Delete
Alt+E+R Rotate
Alt+E+I Mirror
Alt+E+L+A Add layer
Alt+E+L+R Delete layer
Alt+E+L+O layer sorting
Alt+E+L+L layer alignment
Alt+E+L+T correct pad by drilling
Alt+E+L+S layer scaling (used when the character height is not enough)
Alt+E+H+D Change D code
Alt+E+H+T+T Change text
Alt+E+H+E+A breaks everything
Alt+E+H+S breaks up the arc
Alt+E+H+O+S Change origin
Alt+E+T+L line cut
Alt+E+T+C Circle cut
Alt+E+N+J connect nodes
Alt+E+V move node
Alt+E+A Add node Alt+E+E
Delete node
Alt+E+G delete line segment
Increase
Alt+A+F Add pad
Alt+A+L Add line
Alt+A+P adds polygons (for plating edges, choke points and meshes)
Alt+A+X add text
Alt+A+R adds a rectangle
Alt+A+C+C center radius to draw a circle
Alt+A+A+3 Draw an arc with three points
view
Alt+V+C View composite layers
information
Alt+I+M+P measures the distance from point to point (center to center)
Alt+I+M+O measures the distance from object to object (edge to edge, the minimum distance between two objects)
Alt+I+R+D View D code information (used when making text width)
utility
Alt+U+R line to custom
Alt+U+D+I line to pad manual conversion
Alt+U+Y+D extracts large copper skin
Alt+U+Y+R Fill large copper skin
Alt+U+O+C delete duplicate data
Alt+U+O+I delete independent pad (for inner layer positive film)
Alt+U+T add teardrops
Alt+U+Z overall zoom
Alt+U+C quickly generates composite layers
analyze
Alt+N+R DRC detection (check whether the line width and line spacing meet the factory's process requirements)
Alt+N+O Calculate the copper area (plating area=copper area/PANL area*100%)
sheet
Alt+O+N enter NC editing
Alt+T+C to edit composite layers
set up
Alt+S+U Set units
Alt+S+T set characters
Alt+M+M More macro commands The following are the commands after entering NC editing
Alt+E+L+N Add new NC layer (note: be sure to select the corresponding tool table when adding)
Alt+E+H+I+A increases the intersection point of the gong belt (used when the gong belt is deformed)
Alt+E+H+F Change the order of drilling holes
Alt+E+H+H Change drilling
Alt+E+S Delete the gong belt line segment
Alt+A+H Add drilling
Alt+A+S adds slot
Alt+A+C increases hole expansion
Alt+U+F Offset gong belt path (also called gong knife compensation)
Alt+U+O Optimize drilling
Alt+U+D Gerber to drill
Alt+N+D detect drilling
The above is a collection of CAM350 shortcut keys and commands brought by the editor. I hope it can help everyone use CAM350 more conveniently and quickly.
