In order to use Altium Designer17 conveniently and quickly, we often use some shortcut keys. So do you know what the Altium Designer17 shortcut keys are? Next, the editor will bring you an introduction to Altium Designer17 shortcut keys. You can take a look.

Engineering (C):

1. Engineering(C)menu C

2. Select the open project file Ctrl+Alt+O

Place(P):

1.Place(P)menu P

2. Wiring P+L

Design(D):

1.Design(D)menu D

2. Configure the layer color L

3. Wiring rule setting D+R

Tools(T):

1.Tools(T)menu T

2. Browse conflicts Shift+V

3. Browse objects Shift+X

4.Device layout(O)menu I

5.Cancel wiring(U)menu U

Report(R):

1. Report(R)menu R

2.Measure the distance between two points Ctrl+M

Window:

1.Window menu W

2. Tile all open documents Shift+F4

Help(H):

1.Help(H)menu H

2.Filter(F)menu Y

3. Clear the current filter Shift+C

4.Jump grid(G)menu G

5. Run the Raster Properties Editor Ctrl+G for the raster under the cursor

6.Network list(N)menu N

7.Option(O)menu O

8. Configure show/hide parameter options Ctrl+D

9.Zoom(Z)menu Z

10. Refresh the current layer Alt+End

11. Add keyframes to 3D animation menu Alt+Ctrl+K

PCB shortcut keys:

1. Zoom in in small increments Shift+PgUp

2. Reduce in small increments Shift+PgDn

3. Zoom to 400% Ctrl+PgUp

4. Display the next enabled signal layer Multiply

5. Display the previous enabled signal layer Shift+ Multiply

6. Move the mouse up 10 jump grid units Shift+Up

7. Move the mouse down 10 jump grid units Shift+Down

8. Move the mouse 10 jump grid units to the left Shift+Left

9. Move the mouse 10 jump grid units to the right Shift+Right

10. Move the mouse up 1 jump grid unit Up

11. Move the mouse down 1 jump grid unit Down

12. Move the mouse 1 jump grid unit left Left

13. Move the mouse right 1 jump grid unit Right

14. Display the previous device in the library Alt+Left

15. Display the next device in the library Alt+Right

16.Show next enabled layer Plus

17. Display the last enabled layer Minus

18. Paste Alt+Insert on the current layer

19. Switch to single layer mode Shift+S

20. Switch wiring mode Shift+R

21. Switch PCB Object Inspector F11

22. Switch PCB object list Shift+F12

23. Switch PCB filter F12

24. Open the next Tab window Ctrl+Tab

25. Open the previous Tab window Shift+ Ctrl+Tab

26. Display the selected memory dialog box Ctrl+Q

27. Tie floating panel visibility F4

28. Move up to select 10 jump grid units Ctrl+ Shift+Up

29. Move down to select 10 jump grid units Ctrl+ Shift+Down

30. Move left to select 10 jump grid units Ctrl+ Shift+Left

31. Move right to select 10 jump grid units Ctrl+ Shift+Right

32. Move up to select 10 jump grid units Ctrl+Up

33. Move down to select 10 jump grid units Ctrl +Down

34. Move left to select 10 jump grid units Ctrl+Left

35. Move right to select 10 jump grid units Ctrl+ Right

36Clear And Select Neighbors Ctrl+Delete

37.Clear For Routing Unwind Backspace

38. The NET network of the entire line is highlighted. Ctrl + mouse click on a line.

39. Switch between Top and Bottom layers using the numpad* (star key)

40. Switch all displayed layers in turn using the small keyboard +, -

41. Flip all selected components over M+I

42. Device Union Right-click and select Union-Generate Union from Selected Devices

43. Cancel the device union. Right-click and select Union-dissolve the device from the union.

44. Delete line E+D

45. Capture pad View - Grid - Switch electrical grid (shift + E)

Schematic:

1. Hold down Shift and drag a component to quickly copy the component

2. Press and hold the mouse wheel and slide the mouse up and down to zoom in and out.

3. Hold down Ctrl + right mouse button and slide the mouse up and down to zoom in and out.

4. Hold down Ctrl and drag a component to move the position and maintain the original line connection.

5. About the Net Part attribute when drawing the schematic diagram in layers. In the project –options setting.

6. When creating a component, sometimes a component is divided into two parts, Part1 and Part2. First create a new component, and then click Tools New Part.

7. T+C cross probe to find the corresponding component locations on the schematic diagram and PCB.

File(F):

1.File(F)menu F

2. Display the file panel Ctrl+N

3. Open any existing file Ctrl+O

4. Close the current file Ctrl+F4

5.Print the current file Ctrl+P

6. Exit from the application Alt+F4

Edit(E):

1.Edit(E)menu E

2.Cancel Ctrl+Z

3. Clear Delete

4.Select(S)menu S

5.Selects next overlapped object Tab

6. Select the shape and content Ctrl+B

7. Select the connected copper Ctrl+H

8. Uncheck Select(E)menu X

9. Rubber stamp Ctrl+R

10.Mobile(M)menu M

11.Align(G)menu A

12. Align the device with the left edge (the above device shall prevail) Shift+Ctrl+L

13. Align the device with the right edge (the above device shall prevail) Shift+Ctrl+R

14. Align the device with the left edge (the following devices shall prevail) Shift+ Alt +L

15. Align the device with the right edge (the following devices shall prevail) Shift+ Alt +G

16. Make the horizontal spacing of devices equal Shift+Ctrl+H

17. Align the device with top Shift+Ctrl+T

18.Align the device to the bottom Shift+Ctrl+B

19. Align the device with top Shift+ Alt +I

20. Align the device to the bottom Shift+ Alt +N

21. Make the vertical spacing of the devices equal Shift+Ctrl+V

22. Move the selected device to the grid Shift+Ctrl+D

23.Jump(J)menu J

24. Jump to the absolute origin Ctrl+Home

25. Jump to the current origin Ctrl+End

26. Create query Shift+B

27. Find similar objects Shift+F

View(V):

1.View(V)menu V

2.Board shape Editor 1

3. Switch to the setting that most recently used 2D display 2

4. Switch to the setting that most recently used 2D display 3

5. Fit file Ctrl+PgDn

6. Zoom into PgUp

7. Reduce PgDn

8.Panel Home

9. Refresh all visible layers End

10.Set the camera to rotate vertically to 0

11. Set the camera rotation to be perpendicular to the board and rotate 90° 9

12.Set camera rotation to see board in orthogonal view in 3D 8

13. Anchor 3D view cursor trajectory (on/off) Shift+F3

14.Switch folded view in 3D 5

15. Switch to full screen mode Alt +F5

16. Improve shielding level]

17. Reduce shielding level [

18. Anchor solved F6

19.Toolbars menu B

20.Workspace Panels menu K

21.Open the Workspace Control panel Ctrl+’

22. Insight board menu F2

23. Switch the current head display Shift+H

24. Switch overhead tracking Shift+G

25.Reset top deviation origin Insert

26. Switch the origin of overhead deviation Shift+D

27. Switch the insight board lens Shift+M

28. Move the Insight Board lens to the mouse Ctrl+Shift+N

29. Switch the Insight Board lens by following Shift+N

30. Switch the insight board lens to automatically zoom Ctrl+Shift+M

31. Switch the single-layer mode of the insight board lens Ctrl+Shift+S

32. Switch electrical grid Shift+E

33. Set the X and Y jump grids to the given values ​​at the same time Shift+Ctrl+G

34.Switch unit Q

35. Show/hide different silk screens Shift+O

36. Navigate to the next difference F8

37. Navigate to previous difference F7

The above is the introduction of Altium Designer17 shortcut keys brought by the editor. I hope it can help everyone.