Don’t know what the shortcut keys of Altium Designer10 are? Then for those who don’t know, come and take a look at the list of Altium Designer10 shortcut keys brought by the editor. I hope that this tutorial can help everyone.
1. Design browser shortcut keys:
Left-click the mouse——————Select the document at the mouse position
Double-click the mouse——————Edit the document at the mouse position
Right-click the mouse to display the relevant pop-up menu
Ctrl+F4——————Close the current document
Ctrl+Tab——————Cycle through the opened documents
Alt+F4————————Close the design browser DXP
2. Common shortcut keys for schematic diagram and PCB:
Shift————————Quickly pan when panning automatically
Y————————When placing components, flip them up and down
X————————When placing components, flip left and right
Shift+↑↓←→——————The arrow direction moves the cursor in ten grid increments
↑↓←→——————The direction of the arrow moves the cursor in increments of one grid
SpaceBar——————Abandon screen refresh
Esc————————Exit the current command
End——————Screen refresh
Home——————Refresh the screen with the cursor as the center
PageDown, Ctrl+mouse wheel——zoom out the screen with the cursor as the center
PageUp,—Ctrl+mouse wheel—centered on the cursor to prevent large screen
Mouse wheel————Move the screen up and down
Shift+mouse wheel————Move the screen left and right
Ctrl+Z————————Undo the last operation
Ctrl+Y————————Repeat the last operation
Ctrl+A————————Select all
Ctrl+S————————Save the current document
Ctrl+C————————Copy
Ctrl+X————————Cut
Ctrl+V————————Paste
Ctrl+R——————Copy and paste the selected object repeatedly
Delete————————Delete
V+D——————Display the entire document
V+F————————Display all objects
X+A————————Cancel all selected objects
Click and hold the right mouse button to display the sliding hand and move the screen
Click the left mouse button————Select the object
Right-click the mouse to display the pop-up menu or cancel the current command
Right-click the mouse and select Find—Similar————Select the same object
Click the left mouse button and hold down to drag————Select objects inside the area
Click and hold the left mouse button——————Select the object where the cursor is located and move it
Double-click the left mouse button————Edit object
Shift+click the left mouse button————Select or deselect
TAB——————————Edit the properties of the object being placed
Shift+C—Clear the currently filtered objects
Shift+F—to select the same object as
Y——————pop up the quick query menu
F11————————Open or close the Inspector panel
F12————————Open or close the List panel
3. Schematic shortcut keys:
Alt——————————Limit object movement in horizontal and vertical lines
——————Cycle through snap grid settings
Spacebar————rotate 90 degrees when placing an object
Spacebar————Enable start/stop mode when placing wires, buses, and polygon lines
Shift+Spacebar————Switch placement mode when placing wires, buses, and polygon lines
Backspace——Delete the last corner when placing wires, buses, and polygon lines
Click and hold the left mouse button + Delete - delete the corner of the selected center line
Click and hold the left mouse button + Insert - add a corner to the selected line
Ctrl+click and drag the left mouse button——drag the selected object
4. PCB shortcut keys:
Shift+R——————Switch between three wiring modes
Shift+E——————Turn on or off the electrical grid
Ctrl+G————————Pop up the Capture Grid dialog box
G——————Pop up the capture grid menu
N——————Hide mesh lines when moving components
L——————Mirror components to another layout layer
Backspace key————Delete the last corner when routing copper wire
Shift+Spacebar————Switch corner mode when laying copper wires
Spacebar————————Change start/end mode when laying copper wire
Shift+S——————Toggle on/off single-layer display mode
O+D+D+Enter——————Select sketch display mode
O+D+F+Enter——————Select normal display mode
O+D————————Show/hide Prefences dialog box
L——————Display the Board—Layers dialog box
Ctrl+H————————Select the connecting copper wire
Ctrl+Shift+Left-Click——Break line
+————————Switch to the next level (numeric keypad)
————————Switch to the previous layer (numeric keyboard)
*————————Next wiring layer (numeric keypad)
M+V————————Move the vertices of the split plane layer
Alt————————Switch between avoiding obstacles and ignoring obstacles
Ctrl——————Temporarily do not display the electrical grid during wiring
Ctrl+M or R-M————Measure distance
Shift+Spacebar——————Rotate the moving object clockwise
Spacebar————————Rotate the moving object counterclockwise
Q——————Unit switching between metric and imperial systems
E-J-O————Jump to the current origin
E-J-A————Jump to the absolute origin
The above is the list of Altium Designer10 shortcut keys brought by the editor. Friends in need should not miss it.
