Maybe some friends still don’t know how to use the mouse to control Microsoft Flight Simulator

When flying, right-click with the mouse, and there will be a blue frame. There is a joystick at the bottom of the frame. You can press it. Because there is no joystick, it defaults to the mouse as the joystick. If it moves left, it will move left, if it moves up it will fly down, if it moves down it will raise the nose or take off, and vice versa.

Complete list of keyboard operation commands:

1. The simulator command pauses P or Break

2.Full screen mode ALT +Enter

3. Show menu or hide ALT

4. Show or hide ATC menu •ACCENT or SCROLL LOCK

5. Show or hide the kneeboard (Kneeboard) Shift + F10

6. Sound switch Q

7.Reset current flight CTRL + ;(semicolon)

8.Save flight; (semicolon)

9. Exit flight simulation CTRL+C

10. Exit flight simulation immediately CTRL + Break

11. Joystick (disable/use) CTRL + K

12. Global coordinates/frame rate Shift + Z

13.Select the first 1

14. Select the second 2

15. Select the third 3

16. Select the fourth 4

17. Select time compression R

18. Airdrop supplies SHIFT + D

19. Request a fuel truck SHIFT + F

20. Show or hide aircraft labels CTRL + SHIFT + L

21. Show or hide flying skills CTRL + SHIFT + X

22. Increase choice =

23. Slowly increase the selection SHIFT + =

24. Slowly decrease selection SHIFT+ -

25. Reduce your choices -

26. Capture screenshots V

27. Mobile covered bridges (jetways) CTRL + J

28. The aircraft control surface commands the aileron to tilt left. Numeric keyboard 4

29. Aileron tilt right Numeric keyboard 6

Aileron left trim CTRL + numeric keypad 4

30. Aileron right trim CTRL + numeric keyboard 6

31. Vertical tail right yaw numeric keyboard Enter

32. Vertical tail left yaw numeric keyboard 0

33. Vertical tail right trim CTRL + numeric keyboard Enter

34. Vertical tail left trim CTRL + numeric keyboard 0

35. Center the aileron or vertical stabilizer. Numeric keypad 5

36.Horizontal elevator down numeric keypad 8

37.Horizontal elevator up numeric keypad 2

38. Elevator trim down numeric keypad 7

39. Elevator Trim Up Numeric Keyboard 1

40. Flaps fully retracted F5

41.Slowly retract the flaps F6

42. Extend the flaps slowly F7

43. Flaps fully extended F8

44.Extend/retract spoilers /

45. Preposition spoiler SHIFT + /

46. ​​Engine control command selects engine E+engine number

47.Select all engines E+1+2+3+4

48. Cut off the throttle valve F1 (the throttle valve is the accelerator)

49. Recoil (turbofan engine/jet engine) Press and hold F2

50. Lower the throttle valve F2

51. Add throttle F3

52. Throttle valve maximum F4

53. Propeller low speed CTRL + F1

54. Propeller Increase speed CTRL + F

55. Propeller high speed CTRL + F4

56. Oil and gas mixture idle cutoff CTRL+ SHIFT +F1

57. Oil and gas mixing, rapid oil lean CTRL+ SHIFT +F2

58. Oil and gas mixture rich oil CTRL+ SHIFT +F3

59. Oil and gas mixing, completely rich oil CTRL+ SHIFT +F4

60.Magneto selection M

61. Main battery pack or alternator SHIFT+M

62.Jet engine start button J

63. Helicopter rotor clutch switch SHIFT+ .(period)

64. Helicopter rotor regulator switch SHIFT+, (comma)

65.Helicopter rotor brake switch SHIFT+B

66. Add options (such as zooming in) = (equal sign)

67. Slowly increase selection SHIFT+ =

68. Slowly decrease selection SHIFT + -

69. Reduce your choices -

70. General aviation aircraft control command brake (when parked) CTRL +.

71. Control the tail wheel to turn left and right SHIFT+P, then 1 and 2

72.Brake switch .(period)

73.Left brake numeric keyboard +

74. Right brake numeric keypad -

75.Retract and retract landing gear G

The above is the method of using the mouse to control Microsoft Flight Simulator x brought by the editor. Friends who are interested should not miss it.