Don’t know what the shortcut keys of Altium Designer10 are? Then for those who don’t know, come and take a look at the list of Altium Designer10 shortcut keys brought by the editor. I hope that this tutorial can help everyone.

1. Design browser shortcut keys:

Left-click the mouse——————Select the document at the mouse position

Double-click the mouse——————Edit the document at the mouse position

Right-click the mouse to display the relevant pop-up menu

Ctrl+F4——————Close the current document

Ctrl+Tab——————Cycle through the opened documents

Alt+F4————————Close the design browser DXP

2. Common shortcut keys for schematic diagram and PCB:

Shift————————Quickly pan when panning automatically

Y————————When placing components, flip them up and down

X————————When placing components, flip left and right

Shift+↑↓←→——————The arrow direction moves the cursor in ten grid increments

↑↓←→——————The direction of the arrow moves the cursor in increments of one grid

SpaceBar——————Abandon screen refresh

Esc————————Exit the current command

End——————Screen refresh

Home——————Refresh the screen with the cursor as the center

PageDown, Ctrl+mouse wheel——zoom out the screen with the cursor as the center

PageUp,—Ctrl+mouse wheel—centered on the cursor to prevent large screen

Mouse wheel————Move the screen up and down

Shift+mouse wheel————Move the screen left and right

Ctrl+Z————————Undo the last operation

Ctrl+Y————————Repeat the last operation

Ctrl+A————————Select all

Ctrl+S————————Save the current document

Ctrl+C————————Copy

Ctrl+X————————Cut

Ctrl+V————————Paste

Ctrl+R——————Copy and paste the selected object repeatedly

Delete————————Delete

V+D——————Display the entire document

V+F————————Display all objects

X+A————————Cancel all selected objects

Click and hold the right mouse button to display the sliding hand and move the screen

Click the left mouse button————Select the object

Right-click the mouse to display the pop-up menu or cancel the current command

Right-click the mouse and select Find—Similar————Select the same object

Click the left mouse button and hold down to drag————Select objects inside the area

Click and hold the left mouse button——————Select the object where the cursor is located and move it

Double-click the left mouse button————Edit object

Shift+click the left mouse button————Select or deselect

TAB——————————Edit the properties of the object being placed

Shift+C—Clear the currently filtered objects

Shift+F—to select the same object as

Y——————pop up the quick query menu

F11————————Open or close the Inspector panel

F12————————Open or close the List panel

3. Schematic shortcut keys:

Alt——————————Limit object movement in horizontal and vertical lines

——————Cycle through snap grid settings

Spacebar————rotate 90 degrees when placing an object

Spacebar————Enable start/stop mode when placing wires, buses, and polygon lines

Shift+Spacebar————Switch placement mode when placing wires, buses, and polygon lines

Backspace——Delete the last corner when placing wires, buses, and polygon lines

Click and hold the left mouse button + Delete - delete the corner of the selected center line

Click and hold the left mouse button + Insert - add a corner to the selected line

Ctrl+click and drag the left mouse button——drag the selected object

4. PCB shortcut keys:

Shift+R——————Switch between three wiring modes

Shift+E——————Turn on or off the electrical grid

Ctrl+G————————Pop up the Capture Grid dialog box

G——————Pop up the capture grid menu

N——————Hide mesh lines when moving components

L——————Mirror components to another layout layer

Backspace key————Delete the last corner when routing copper wire

Shift+Spacebar————Switch corner mode when laying copper wires

Spacebar————————Change start/end mode when laying copper wire

Shift+S——————Toggle on/off single-layer display mode

O+D+D+Enter——————Select sketch display mode

O+D+F+Enter——————Select normal display mode

O+D————————Show/hide Prefences dialog box

L——————Display the Board—Layers dialog box

Ctrl+H————————Select the connecting copper wire

Ctrl+Shift+Left-Click——Break line

+————————Switch to the next level (numeric keypad)

————————Switch to the previous layer (numeric keyboard)

*————————Next wiring layer (numeric keypad)

M+V————————Move the vertices of the split plane layer

Alt————————Switch between avoiding obstacles and ignoring obstacles

Ctrl——————Temporarily do not display the electrical grid during wiring

Ctrl+M or R-M————Measure distance

Shift+Spacebar——————Rotate the moving object clockwise

Spacebar————————Rotate the moving object counterclockwise

Q——————Unit switching between metric and imperial systems

E-J-O————Jump to the current origin

E-J-A————Jump to the absolute origin

The above is the list of Altium Designer10 shortcut keys brought by the editor. Friends in need should not miss it.